List of Tools and Materials
- Wallpaper
- Knife
- Measurement Tape
- Smoothing Tool
Installation Guide
- First step is to make sure your wall is ready for the install wallpapers.
- Remove all Nails, Screws or hooks on the wall. If there are Cracks or holes in wall, apply wall putty first.
- If you have old wallpaper on the wall, remove them.
- Measuring your wall Height and width using Measurement Tape.
- Then spread out your Wallpaper. Unroll it gently on a table or floor.
- Based on your wall size, wallpaper will come 2 or 3 parts.
- Each part with white boarders will come. cut it white line in all sides and all parts.
Past your First Part:
- Take it first panel and peal it backside paper and apply on the wall gently. Lay it from the ceiling and smooth it down the wall with a smoothing tool. Leave out about 2 inches hanging at the top and bottom.
- Using smoothing tool remove all bubbles top to bottom and cut excess paper on top and bottom.
Past your 2nd and remaining parts:
- Second part is harder than first part. You have to match up patterns and avoid overlay.
- Focus on matching the designs and make sure the paper does not overlap. The 2nd part must meet the first part at the edge.
- Once again leave few inches top and bottom. Using smoothing tool to remove bubbles and cut excess paper top and bottom.
- If already have a Switchboard or Tube Light or Bulb on the wall, just lay the wallpaper over them, but don’t press the paper down too much on these areas. Use your knife to cut through at the center point. Then press the paper down and smooth it around the edges of the socket. When the paper has rested well, the shape of the outlet will be more definite, then cut the excess paper with a knife.
- Same process do on Remaining parts.
List of Tools and Materials
- Wallpaper
- Knife
- Measurement Tape
- Smoothing Tool
Installation Guide
- First step is to make sure your wall is ready for the install wallpapers.
- Remove all Nails, Screws or hooks on the wall. If there are Cracks or holes in wall, apply wall putty first.
- If you have old wallpaper on the wall, remove them.
- Measuring your wall Height and width using Measurement Tape.
- Then spread out your Wallpaper. Unroll it gently on a table or floor.
- Based on your wall size, wallpaper will come 2 or 3 parts.
- Each part with white boarders will come. cut it white line in all sides and all parts.
Adhesive Mixing:
Take the one liter water in bucket and add our CMC powder mix 25 to 30 grams and Gently mix 5mins, it will turn a paste.
Paste your First Part:
- Take it first panel and apply the paste in back side of panel
- Lay it from the ceiling and smooth it down the wall with a smoothing tool. Leave out about 2 inches hanging at the top and bottom.
- Using smoothing tool remove all bubbles top to bottom and cut excess paper on top and bottom.
Past your 2nd and remaining parts:
- Second part is harder than first part. You have to match up patterns and avoid overlay.
- Focus on matching the designs and make sure the paper does not overlap. The 2nd part must meet the first part at the edge.
- Once again leave few inches top and bottom. Using smoothing tool to remove bubbles and cut excess paper top and bottom.
- If already have a Switchboard or Tube Light or Bulb on the wall, just lay the wallpaper over them, but don’t press the paper down too much on these areas. Use your knife to cut through at the center point. Then press the paper down and smooth it around the edges of the socket. When the paper has rested well, the shape of the outlet will be more definite, then cut the excess paper with a knife.
- Same process do on Remaining parts.
List of Tools and Materials
- Wallpaper
- Knife
- Measurement Tape
- Smoothing Tool
Installation Guide
- First step is to make sure your wall is ready for the install wallpapers.
- Remove all Nails, Screws or hooks on the wall. If there are Cracks or holes in wall, apply wall putty first.
- If you have old wallpaper on the wall, remove them.
- Measuring your wall Height and width using Measurement Tape.
- Each Wallpaper roll Width 21″ and Length 9.5 meters. If wall size Height 100 inches and width 120 inches, you need 6 panels and each panel height 100 inches. Each roll approximately get 3 panels. So you need 2 Rolls.
- Then spread out your Wallpaper. Unroll it gently on a table or floor.
- Cut 1st panel using knife, take the size in 110 inches.
- Second panel cutting is harder than first panel, because you have to match up patterns and overlay. Unroll your wallpaper and align it next to the first panel, you should start matching the patterns top and bottom. If matched then cut the panel and same process for remaining panels.
Adhesive Mixing:
Take the one liter water in bucket and add our CMC powder mix 25 to 30 grams and Gently mix 5mins, it will turn a paste.
Paste your First Part:
- Take it first panel and apply the paste in back side of panel
- Lay it from the ceiling and smooth it down the wall with a smoothing tool. Leave out about 2 inches hanging at the top and bottom.
- Using smoothing tool remove all bubbles top to bottom and cut excess paper on top and bottom.
Past your 2nd and remaining parts:
- Second part is harder than first part. You have to match up patterns and avoid overlay.
- Focus on matching the designs and make sure the paper does not overlap. The 2nd part must meet the first part at the edge.
- Once again leave few inches top and bottom. Using smoothing tool to remove bubbles and cut excess paper top and bottom.
- If already have a Switchboard or Tube Light or Bulb on the wall, just lay the wallpaper over them, but don’t press the paper down too much on these areas. Use your knife to cut through at the center point. Then press the paper down and smooth it around the edges of the socket. When the paper has rested well, the shape of the outlet will be more definite, then cut the excess paper with a knife.
- Same process do on Remaining parts.